Split-Mount-Indoor
IP-50FX200
Die IP-50FX200 vereint drei Komponenten in einem System: Router (CSR), Netzwerk-Switch und Funk-Indoorunit (IDU). Die IP-50FX kann über Glasfaser und Ethernet mit jedem Gerätetyp verbunden werden und unterstützt Funkkonfigurationen von bis zu 16+0. Aufgrund seiner hohen Switching-Kapazität und Portdichte eignet es sich hervorragend für jeden Mobilfunkstandort, der eine hohe Kapazität, sowie Switching- und Routing-Funktionen erfordert.
Die IP-50 unterstützt Layer 1 Link Bonding, Ethernet Bandwidth Notification (ETH-BN) sowie Klasse-C-kompatible Synchronisierung, SyncE, IEEE-1588 Transparent Clock und Boundary Clock
PRODUKT-HIGHLIGHTS Technische Daten
Mechanische Daten
Höhe: 44 mm
Breite: 431.5 mm
Tiefe: 250 mm
Gewicht: 4 kg
Ausstattungsmerkmale
Operation: ETSI EN 300 019-1-3, Class 3.2
0°C bis +55°C
Humidity: 5%RH to 95%RH
Storage: ETSI EN 300 019-1-1 class 1.2 (Weather protected, not temperature-controlled Storage)
Transportation: ETSI EN 300 019-1-2 class 2.3 power (Public transportation)
EMC: Canada/USA Radiated and conducted emissions tests according to ICES-003 and FCC 47 CFR part 15, subpart B Europe according to EN 301 489-1/4 + EN 300 386 India according to TEC/SD/DD/EMC-221/05/OCT-16 + IEC 61000-4-29
Safety: Europe/CB/USA/Canada tests and certification according to EN/IEC/UL/CSA C22.2 NO 62368-1
Power Specifications
IDU Standard Input: -48 VDC with dual power supply feed for power redundancy.
Maximum power consumption with 2xPoE: ~264W
Typical power consumption, not including PoE: ~100W
IDU DC Input range: -40.5 to -60 VDC
SDN
NETCONF/YANG management
Applications
Edge/tail
First and second Aggregation
Networking
Networking capacity: 64 Gbps
Layer-1 carrier bonding: Up to 16+0
Quality of Service: 3 levels of H-QoS
OAM functionality: ETH-BN according to ITUT G.8013/Y.1731
QoS classification based on TOS/DSCP, VLAN ID, VLAN P-bits, MAC DA and SA, SA and DA IP Addresses (IPv4 and IPv6)
LAG support with BFD on LAG interfaces according to RFC7130
Open SW standards: complies with ONL/ONIE
Layer-1 carrier bonding supports multiband with any additional layer-1 connection
Layer 3 Software
IP/MPLS as the infrastructure
LDP for label distribution / Segment Routing with Topology Independent LFA
IGP – OSPFv2/v3, IS-IS for path of the MPLS tunnels with LFA
L3VPN as the service.
MP-BGP as the protocol to establish the end to end L3 services (L3VPN).
BFD to monitor health of connection to aggregation router.
Complies with TWAMP according to RFC 5357
Synchronization
1588 Boundary and Transparent Clock for full timing support from the network – G.8275.1 profile
1588 Boundary and Transparent Clock for partial timing support from the network with GNSS as a main timing source – G.8275.2 profile
Technische Daten
Mechanische Daten
Höhe: 44 mm
Breite: 431.5 mm
Tiefe: 250 mm
Gewicht: 4 kg
Ausstattungsmerkmale
Operation: ETSI EN 300 019-1-3, Class 3.2
0°C bis +55°C
Humidity: 5%RH to 95%RH
Storage: ETSI EN 300 019-1-1 class 1.2 (Weather protected, not temperature-controlled Storage)
Transportation: ETSI EN 300 019-1-2 class 2.3 power (Public transportation)
EMC: Canada/USA Radiated and conducted emissions tests according to ICES-003 and FCC 47 CFR part 15, subpart B Europe according to EN 301 489-1/4 + EN 300 386 India according to TEC/SD/DD/EMC-221/05/OCT-16 + IEC 61000-4-29
Safety: Europe/CB/USA/Canada tests and certification according to EN/IEC/UL/CSA C22.2 NO 62368-1
Power Specifications
IDU Standard Input: -48 VDC with dual power supply feed for power redundancy.
Maximum power consumption with 2xPoE: ~264W
Typical power consumption, not including PoE: ~100W
IDU DC Input range: -40.5 to -60 VDC
SDN
NETCONF/YANG management
Applications
Edge/tail
First and second Aggregation
Networking
Networking capacity: 64 Gbps
Layer-1 carrier bonding: Up to 16+0
Quality of Service: 3 levels of H-QoS
OAM functionality: ETH-BN according to ITUT G.8013/Y.1731
QoS classification based on TOS/DSCP, VLAN ID, VLAN P-bits, MAC DA and SA, SA and DA IP Addresses (IPv4 and IPv6)
LAG support with BFD on LAG interfaces according to RFC7130
Open SW standards: complies with ONL/ONIE
Layer-1 carrier bonding supports multiband with any additional layer-1 connection
Layer 3 Software
IP/MPLS as the infrastructure
LDP for label distribution / Segment Routing with Topology Independent LFA
IGP – OSPFv2/v3, IS-IS for path of the MPLS tunnels with LFA
L3VPN as the service.
MP-BGP as the protocol to establish the end to end L3 services (L3VPN).
BFD to monitor health of connection to aggregation router.
Complies with TWAMP according to RFC 5357
Synchronization
1588 Boundary and Transparent Clock for full timing support from the network – G.8275.1 profile
1588 Boundary and Transparent Clock for partial timing support from the network with GNSS as a main timing source – G.8275.2 profile
Datenblatt Download
